Tampa Rubber and Gasket
Tampa Rubber Home PageTampa Rubber CatalogTampa Rubber Order FormTampa Rubber Line CardDirections to Tampa Rubber

CONVEYOR BELT MAINTENANCE PRODUCTS



Far-Pul HD Belt Clamps

Far-Pul HD
Belt Clamps
Unique Design, Rugged Construction
Here is the easy-to-use, lightweight and sturdy belt clamp, specially engineered for heavy duty applications.
 
With a load capacity up to three tons when used with two 1-½ ton come-alongs, it securely grips belts up to 1" thick. And it adjusts easily to fit a variety of belt widths, eliminating the need to inventory different clamp bars for different widths.
  • Provides even tensioning across the entire belt width.
  • Clamp bars held in place from the outside. Scissors slide easily into place against both belt edges for easy adjustability.
  • Extruded aluminum construction resists corrosion and seizing in wet environments.
Belt
Width
Ordering
Number
Up to 30"LSHD30
Up to 36"LSHD36
Up to 42"LSHD42
Up to 48"LSHD48
Up to 54"LSHD54
Up to 60"LSHD60
Up to 72"LSHD72
Far-Pul HD
Belt Clamps
A complete set of Far-Pul HD Belt Clamps includes four clamp bars, and four clamp scissors with carry bag. Come-alongs not included.



840 Series Belt Cutter

840 Series
Belt Cutter
Make straighter cuts - time after time - with the lightweight, easy-to-use 840 Series aluminum belt cutter.
 
Designed to enhance operator safety on belts up to 84" wide, the 840 Cutter grips belts securely. The chain-driven, double-edged safety blade is shielded from operator contact, and cuts rubber or PVC belts up to 1" thick. The blade can be driven from either end of the cutter and cuts in both directions.
Belt
Width
Ordering
Number
Up to 36"840836
Up to 48"840848
Up to 60"840860
Up to 72"840872
Up to 84"840884
840 Series
Belt Cutter



Alligator 300 Series Belt Cutter

For belts of any width up to 1-1/8" thick, the Alligator 300 series belt cutter delivers clean, straight cuts quickly and safely. The double-edged blade cuts in either direction. An extra-long blade can also be special ordered for belts up to 1-9/16" thick.
Belt
Width
Ordering
Number
Up to 12"300312
Up to 18"300318
Up to 24"300324
Up to 30"300330
Up to 36"300336
Up to 42"300342
Up to 48"300348
Up to 60"300360
300 Series
Belt Cutter



Flexco Belt Grips

Pulling conveyor belting by hand is a lot easier with a Flexco Belt Grip. When the belt grip is slipped over the belt edge at a right angle, belts can be pulled without damaging the belt surfaces. Belt grips can be used on belts up to 5/8" thick and come in pairs.
DescriptionOrdering
Number
Sold by the pair22
Flexco
Belt Grips



FSK Belt Skiver

FSK Belt
Skiver
Portable, lightweight skiver adjusts easily and precisely to various cutting depths. It's easy to carry and operate around the job site - even in cramped operating environments. Use on rubber-covered belts with top covers of 3/16" or more. Provides skives from 1/16" to 3/8" deep in a single pass. Deeper skives can be achieved with multiple passes. Cutting depth is gauged from the bottom of the belt surface, so the FSK can be used on most worn belt surfaces.
DescriptionOrdering
Number
Skiver CompleteFSK-1
FSK Belt
Skiver



Flexco Belt Groover

The belt groover makes it easy to cut a groove into the belt surface, permitting the leading edge of belt splices to "nest" at or below the belt surface, thereby reducing splice profile. Can also be used to cut a series of grooves to countersink entire splices.
DescriptionOrdering
Number
Belt GrooverFBG1
Flexco
Belt Groover



Persuader Conveyor Belt Positioner

The Persuader Conveyor Belt Positioner is a dependable, field-proven solution for the lost production time and repair costs associated with off-center loading and belt mistracking.

The simple, easy-to-install solution for belt mistracking.
The Persuader features an innovative design: rollers make smooth contact with the return belt's bottom cover, centering it into the correct path and holding it there. This centering action at the critical loading point solves many top-side tracking problems. In fact, most top-side tracking problems can be solved with a single Persuader at the tail pulley.Persuader Conveyor
Belt Positioner

 
Heavy-Duty XL Persuader for wider, higher-tension belts.
For thicker, higher-tension steel-cable belts, and belts between 72" and 96" wide, choose the Heavy-Duty XL Persuader. It combines the design and performance advantages of the Persuader, with CEMA E rollers and bearings.Heavy-Duty
XL Persuader
Persuader Conveyor Belt Positioner *
DescriptionBelt Width
(Min-Max)
Persuader Width
(Min-Max)
Ordering
Number
Small18"-24"24"-34"CBP-S
Medium30"-48"34"-56"CBP-M
Large54"-72"56"-83"CBP-L
Extra Large72"-96"72"-120"CBP-X
* Persuader comes standard with Exalon rollers.
Use next larger size for belt widths between ranges.
Idler Rollers on Sizes S,M and L are CEMA D.
Idler Rollers on the XL Size are CEMA E.
Persuader Conveyor Belt Positioner
with Steel Rollers
DescriptionBelt Width
(Min-Max)
Persuader Width
(Min-Max)
Ordering
Number
Small18"-24"24"-34"PSR-S
Medium30"-48"34"-56"PSR-M
Large54"-72"56"-83"PSR-L
Extra Large72"-96"72"-120"PSR-X
* Use next larger size for belt widths between ranges.
Idler Rollers on Sizes S,M and L are CEMA D.
Idler Rollers on the XL Size are CEMA E.



Deflector Belt Plows

Specially designed belt cleaners for the tail pulley, Deflector Belt Plows feature an exclusive, innovative blade design. The blade's 20º leading edge "spirals" debris off the inside of the belt. Compare this to ordinary flat-blade plows and homemade devices that often just let debris roll under the blade.

Deflector V-Plow *
  • Self-adjusting unit eliminates the need to readjust to accommodate blade wear.
  • Turnbuckle permits precise adjustment so the plow can be fine-tuned to the belt at installation and eliminate unit vibration.
  • Can also be positioned directly behind the head pulley to dump debris right at the transfer point.
DescriptionBelt Width
(Min-Max)
Ordering
Number
Extra Small18"-24"CBV-XS
Small30"-36"CBV-S
Medium42"-48"CBV-M
Large54"-60"CBV-L
72"72"CBV-72
84"84"CBV-84
96"96"CBV-96
* Use next larger size for belt widths between ranges.
Deflector
V-Plow

 
Deflector Diagonal Plow *
  • Installed on a 45º angle across the belt to discharge debris to one side of the belt.
  • Blade is installed in a fixed position, eliminating bouncing problems associated with some floating style plows.
DescriptionBelt Width
(Min-Max)
Ordering
Number
Small18"-30"CBD-S
Medium36"-42"CBD-M
Large48"-60"CBD-L
* Use next larger size for belt widths between ranges.
Deflector
Diagonal Plow

 
Deflector Heavy-Duty Reversing Diagonal Plow *
  • Twin-bladed plow designed to clean belt in both directions of travel.
  • Discharge material to either side of the belt.
  • Installs securely to conveyor structure and will work on conveyors with severe belt vibration.
DescriptionBelt Width
(Min-Max)
Ordering
Number
Small18"-30"CBR-S
Medium36"-42"CBR-M
Large48"-60"CBR-L
72"72"CBR-72
84"84"CBR-84
96"96"CBR-96
* Use next larger size for belt widths between ranges.
Deflector Heavy-Duty
Reversing Diagonal Plow



Flex-Lok Conveyor Skirt Clamp



Our versatile skirt clamp design makes it easy to eliminate loading-point spillage on any conveyor loading site - even in severe heavy-loading applications.
 
Flex-Lok is ideal on perpendicular or vertical skirt boards. The unique design ensures that, once properly installed, the skirt rubber will not rub on the belt causing premature wear or gouge marks on the belts.
Flex-Lok Conveyor
Skirt Clamps

 
Easy Installation and Quick Adjustment
Flex-Lok utilizes a unique clamp pin and wedge lock assembly, so the assembly can be locked in any position 360º around the pin. The remaining parts interlock, too, allowing one person to reposition or replace skirt rubber. The clamp plates and pins can be placed in various positions along the clamp runners - even in the most restrictive environments.The captive wedge in the clamp pin insures that no parts get lost.Flex-Lok Conveyor
Skirt Clamps
Clamp plate secures skirt rubber in proper position to insure no damage is caused to the belt.
Restraining bar is held in place by clamp plates so hands are free to adjust skirt rubber.
DescriptionOrdering
Number
Skirt Clamp CompleteFLSC-1
New expanded belt thickness range: standard, 5/16" to 1"; mini, 5/16" to 5/8"
Flex-Lok comes in standard 6' lengths, and can be easily modified for shorter length requirements.
One 6' skirt clamp includes one 6' clamp runner, 4 clamp plates, 4 clamp pins and one 6' restraining bar.



Mini Flex-Lok for Confined Space Applications

With an overall height of just 5-1/2", the Mini Flex-Lok is the ideal remedy for loading-point spillage in restricted space applications.
DescriptionOrdering
Number
Mini Skirt Clamp CompleteFLSCM-1
Mini Flex-Lok
Skirt Clamp
One 6' mini skirt clamp includes one 6' clamp runner, 3 mini clamp plates, 3 clamp pins and one 6' restraining bar.

line

GO TO TABLE OF CONTENTS

GO TO MAIN PAGE

line

Tampa Rubber & Gasket Co., Inc.

215 North 20th Street
Tampa, FL, USA 33605
Ph-813-247-3647 Fax-813-247-3180
Toll Free-800-940-4673 E-Mail - The Post Office
Visa Mastercard
American Express Discover
We accept Visa, Mastercard, American Express & Discover


Validated!
click here

w3c Validated
COPYRIGHT © 1998-2004 TAMPA RUBBER & GASKET CO., INC.